Skip to content

30A Flush Mount PWM Solar Charge Controller 12/24V with LCD Display

SKU MP3764
Original price $149.00 - Original price $149.00
Original price
$149.00
$149.00 - $149.00
Current price $149.00
2 Year Warranty

This flush mount solar charge controller enables you to keep an eye on your power system without having to stare at an unsightly controller cluttering your RV or boat’s interior. The intelligent system features a PWM charger with bulk, boost/equalise, and float modes to keep your Lead Acid or LiFeP04 batteries in peak condition. The integrated LCD indicates real-time energy information, operational parameters, and fault messages, and is easily navigated using the two push buttons. Installation is made easy with pluggable terminals on the rear for the solar panel, battery, and temperature sensor. An RS485 port enables you to connect a computer for programming purposes, or to a Wi-Fi module (sold separately) so you can control the system from your Smartphone. It has extensive electronic safety protection, and is sure to keep your appliances and gadgets running when you’re away from mains power.
 
Note: To use lithium batteries, the unit must be programmed with the below Wi-Fi adapter or via the RS485 to USB cable in the box.
 
Battery Support:
• Sealed, Gel or flooded Lead (8V - 30V)
• LiFePO4 (4S/12V, 8S/24V)
 
Features:
- 8 - 32VDC Operating Range, 50VDC Maximum Open-Circuit Solar Voltage
- Compatible with Lead acid and LiFePO4 batteries
- Flush mount
- Bulk, Boost/Equalize, Float charging modes
- LCD screen with real-time energy stats, operational and fault message
- Battery temperature compensation
- Remote control; monitor and set parameters via PC or APP
- 10mm2/8AWG Recommended Cable Size (16mm2/6AWG Max)
- Max input: 360W @ 12V, 720W @ 24V
 
Wi-Fi Connection Module (Sold Separately)
Add Wi-Fi communication to the MP3764 Solar Charge Controller with this interface and control your power installation with your Smartphone - up to 50m communication range

Handy Tip Solar Charge Controllers

Directly connecting a solar panel or array to a battery can be catastrophic as solar panels can output a wide voltage range. As an example, a nominal 12 volt rated panel can output anything up to 22volts during an average sunny day. A solar charge controller between the panel and the battery ensures the battery receives the correct output voltage and current from the panel to minimise the risk of the battery being overcharged or discharging back into the panels. Charge controllers come in a variety of types which give different performance and can be matched to simple recreational applications all the way up to complex high power solar array installations.

SWITCHING: Simple switching controllers connect the panel to the battery when the panel is providing power & the battery is not fully charged. This type of controller is low cost and only good for basic solar equipment setups such as standby lighting, etc. where the panel yield is far higher than the load requires. PWM: Pulse width modulated (PWM) controllers continually apply voltage pulses to the battery whenever the panel is providing sufficient voltage. The pulse width (or duration) is varied by the controller depending on the charge state of the battery to ensure the correct amount of charge is harvested from the panel whenever it is available. As a result, PWMc ontrollers provide a much higher power yield than simple switching controllers.

MPPT: Maximum power point tracking (MPPT) controllers maximize power conversion between the panel output and the battery input by using a DC to DC switchmode power converter. By continuously tracking the panel output and adjusting the converter they yield the maximum amount of power under widely varying solar conditions. MPPT controllers give the best solar system efficiency and improve solar system power yield by a significant percentage. Both PWM and MPPT controllers are available with display panels which allow you to track performance of the solar system. Panel voltage, battery voltage, charging current, and total charge supplied can be easily displayed so you can ensure the system is running correctly. More complex models also include integration functions to remotely control other equipment or be linked into advanced systems.

Internal or Sub-part Dimensions


Height
106mm
Dimension details
Width
179mm

Additional Dimensions


Diameter
Dimensions details

Solar Charge Controllers and Regulators


Max PV Open Circuit Voltage
30V
Max Charging Current
30A
Charge Controller Technology
Pulse Width Modulated (PWM)

DC Voltage Rating


DC Voltage
12V, 24V

DC Current Rating


DC current rating
30A

Ingress Protection Rating


IP Rating
IP30
Dust/Particle Ingress Protection
3 - Objects > 2.5mm, Tools, thick wires etc
Liquid/Moisture Ingress Protection
0 - Not protected

Product Dimensions


Depth
49mm
Weight
300g
Width
179mm
Height
106mm

Packaged Dimensions


Packaged Volume
1.65904l
Packaged Weight
0.454kg
Packaged Length
20.9cm
Packaged Width
12.6cm
Packaged Height
6.3cm
Warranty: 24 Months

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare